 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MOTOROLA SEMICONDUCTOR TECHNICAL DATA Dual 1:3 Fanout Buffer The MC100LVEL13 is a dual, fully differential 1:3 fanout buffer. The MC100EL13 is pin and functionally equivalent to the MC100LVEL13 but is specified for operation at the standard 100E ECL voltage supply. The Low Output-Output Skew of the device makes it ideal for distributing two different frequency synchronous signals. The differential inputs have special circuitry which ensures device stability under open input conditions. When both differential inputs are left open the D input will pull down to VEE, The D input will bias around VCC/2 and the Q output will go LOW. MC100LVEL13 MC100EL13 20 * * * * * * Differential Inputs and Outputs 20-Lead SOIC Packaging 500ps Typical Propagation Delays 50ps Output-Output Skews Supports Both Standard and Low Voltage 100K ECL >2000V ESD Protection 1 DW SUFFIX PLASTIC SOIC PACKAGE CASE 751D-04 Logic Diagram and Pinout: 20-Lead SOIC (Top View) Q1a 20 Q1a 19 Q2a 18 Q2a 17 VCC 16 Q2b 15 Q2b 14 Q1b 13 Q1b 12 VEE 11 PIN NAMES Pins Qna, Qna Qnb, Qnb CLKn, CLKn Function Differential Clock Outputs Differential Clock Outputs Differential Clock Inputs 1 Q0a 2 Q0a 3 4 5 6 7 8 9 Q0b 10 Q0b VCC CLKa CLKa CLKb CLKb VCC MC100LVEL13 DC CHARACTERISTICS (VEE = -3.0V to -3.8V; VCC = GND) -40C Symbol IEE IIH IINL Characteristic Power Supply Current Input HIGH Current Input LOW Current Dn Dn 0.5 -300 Min Typ 30 Max 38 150 0.5 -300 Min 0C Typ 30 Max 38 150 0.5 -300 Min 25C Typ 30 Max 38 150 0.5 -300 Min 85C Typ 32 Max 40 150 Unit mA A A 4/95 (c) Motorola, Inc. 1996 4-1 REV 1 MC100LVEL13 MC100EL13 MC100LVEL13 AC CHARACTERISTICS (VEE = -3.0V to -3.8V; VCC = GND) -40C Symbol tPLH tPHL tsk(O) Characteristic Propagation Delay CLK Q/Q Output-Output Skew Any Qa Qa, Any Qb Qb Any Qa Any Qb Duty Cycle Skew |tPLH-tPHL| Minimum Input Swing1 Common Mode Range2 VPP < 500mV VPP 500mV Output Rise/Fall Times Q (20% - 80%) Min 410 Typ Max 600 50 75 50 150 -2.0 -1.8 230 1000 -0.4 -0.4 500 150 -2.1 -1.9 230 Min 420 0C Typ Max 610 50 75 50 1000 -0.4 -0.4 500 150 -2.1 -1.9 230 Min 430 25C Typ Max 620 50 75 50 1000 -0.4 -0.4 500 150 -2.1 -1.9 230 Min 450 85C Typ Max 640 ps 50 75 ps 50 1000 -0.4 -0.4 500 ps mV V Unit ps tsk(DC) VPP VCMR tr tf 1. Minimum input swing for which AC parameters guaranteed. The device has a DC gain of 40. 2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range varies 1:1 with VEE. The numbers in the spec table assume a nominal VEE = -3.3V. Note for PECL operation, the VCMR(min) will be fixed at 3.3V - |VCMR(min)|. MC100EL13 DC CHARACTERISTICS (VEE = -4.2V to -5.5V; VCC = GND) -40C Symbol IEE IIH IINL Characteristic Power Supply Current Input HIGH Current Input LOW Current Dn Dn 0.5 -300 Min Typ 30 Max 38 150 0.5 -300 Min 0C Typ 30 Max 38 150 0.5 -300 Min 25C Typ 30 Max 38 150 0.5 -300 Min 85C Typ 32 Max 40 150 Unit mA A A MC100EL13 AC CHARACTERISTICS (VEE = -4.2V to -5.5V; VCC = GND) -40C Symbol tPLH tPHL tsk(O) Characteristic Propagation Delay CLK Q/Q Output-Output Skew Any Qa Qa, Any Qb Qb Any Qa Any Qb Duty Cycle Skew |tPLH-tPHL| Minimum Input Swing1 Common Mode Range2 VPP < 500mV VPP 500mV Output Rise/Fall Times Q (20% - 80%) Min 410 Typ Max 600 50 75 50 150 -3.2 -3.0 230 1000 -0.4 -0.4 500 150 -3.3 -3.1 230 Min 420 0C Typ Max 610 50 75 50 1000 -0.4 -0.4 500 150 -3.3 -3.1 230 Min 430 25C Typ Max 620 50 75 50 1000 -0.4 -0.4 500 150 -3.3 -3.1 230 Min 450 85C Typ Max 640 ps 50 75 ps 50 1000 -0.4 -0.4 500 ps mV V Unit ps tsk(DC) VPP VCMR tr tf 1. Minimum input swing for which AC parameters guaranteed. The device has a DC gain of 40. 2. The CMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the specified range and the peak-to-peak voltage lies between VPPmin and 1V. The lower end of the CMR range varies 1:1 with VEE. The numbers in the spec table assume a nominal VEE = -4.5V. Note for PECL operation, the VCMR(min) will be fixed at 5.0V - |VCMR(min)|. MOTOROLA 4-2 ECLinPS and ECLinPS Lite DL140 -- Rev 3 MC100LVEL13 MC100EL13 OUTLINE DIMENSIONS DW SUFFIX PLASTIC SOIC PACKAGE CASE 751D-04 ISSUE E -A - 20 11 NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.150 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF D DIMENSION AT MAXIMUM MATERIAL CONDITION. DIM A B C D F G J K M P R MILLIMETERS MIN MAX 12.65 12.95 7.40 7.60 2.35 2.65 0.35 0.49 0.50 0.90 1.27 BSC 0.25 0.32 0.10 0.25 0 7 10.05 10.55 0.25 0.75 INCHES MIN MAX 0.499 0.510 0.292 0.299 0.093 0.104 0.014 0.019 0.020 0.035 0.050 BSC 0.010 0.012 0.004 0.009 0 7 0.395 0.415 0.010 0.029 -B - 1 10 P 10 PL 0.010 (0.25) M B M D 20 PL J M 0.010 (0.25) T A S B S F R X 45 C -T G 18 PL SEATING - PLANE K M Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters which may be provided in Motorola data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE/Locations Not Listed: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1-800-441-2447 or 602-303-5454 MFAX: RMFAX0@email.sps.mot.com - TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, 6F Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 03-81-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852-26629298 ECLinPS and ECLinPS Lite DL140 -- Rev 3 4-3 *MC100LVEL13/D* MC100LVEL13/D MOTOROLA |
Price & Availability of MC100LVEL13
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |